![]() |
The problem: My LG top-load washing machine (WT1101CW) stopped running full cycles and repeatedly displayed an LE error code.
The solution: I tested the motor components, determined that the Hall sensor had failed, and replaced it with an inexpensive aftermarket part.
The cost: Approximately $13–$15 for the replacement Hall sensor.
The result: The washing machine worked again!
Date of Error Code: April 23, 2026
Sometimes the best repair is the one you can do yourself with a few basic tools, a multimeter, and a little patience. Rather than replace the entire washing machine or pay for a service call, I decided to troubleshoot the problem and see if I could fix it. Since the repair the washing machine has been running properly now for over 6 months, not bad for a 10 year old machine. It's not junk yet!
Here's how I diagnosed and repaired my LG WT1101CW washing machine.
Washing Machine Information
Manufacturer: LG
Model: WT1101CW
Description: 4.1 cu. ft. Large Capacity Top Load Washer
Date of failure: April 23, 2026
Error code: LE — Locked Motor Error
Failed component: Hall sensor (rotor position sensor)
Replacement part: 6501KW2002A
Repair cost: Approximately $13–$15
1. The Problem: LG Washer Displays an LE Error Code
The washing machine would start a cycle but stop working approximately 20–30 seconds into the first part of the cycle.
I could hear a soft buzzing sound repeating four or five times. Then the washer would stop, the LE error code would flash on the display, and the machine would play its warning chimes.
The washer wasn't completing its cycle, which meant laundry was piling up until I could figure out what was wrong.
What Does the LE Error Code Mean?
The LE error indicates a locked-motor condition. The washer's control system is having trouble detecting or operating the motor as expected.
Possible causes include:
A disconnected or damaged Hall sensor or its wiring.
A faulty Hall sensor.
A defective stator or motor-related electrical problem.
A mechanical obstruction preventing the drum from rotating.
Locked or damaged bearings.
The error code identifies a problem to investigate, but it doesn't necessarily tell you which component has failed.
| LG Washing Machine Service Manual MODEL : WT1201C*, WT1101C* P/No.: MFL 40322158 (see page 32) |
LG no longer sells the official service manual hardcopy, but you can find it online from some sites with lots of ads. Be careful where you click.
I needed to narrow down the possibilities before ordering parts.
2. Basic Troubleshooting
Before taking the washing machine apart, I tried several simple troubleshooting steps.
Power Cycling the Washer
First, I turned the washing machine off and back on again. Unfortunately, that didn't resolve the problem.
I also unplugged the washer for approximately 10 minutes, then held the Play/Pause button for five seconds as a reset attempt.
The LE error returned.
Checking for Mechanical Obstructions
I checked the wash basin for foreign objects that might prevent the drum from rotating.
I could manually turn the basin, and nothing appeared to be physically blocking the motor.
This didn't completely rule out a mechanical problem, but it made a completely locked drum less likely.
At this point, I needed to investigate the motor assembly and its associated electrical components.
3. Opening the Washer and Investigating the Motor
I removed the rear panel and started looking around.
One thing I discovered was a collection of socks at the bottom of the machine. They didn't appear to be obstructing anything, but it was a good reminder that foreign objects can accumulate in unexpected places.
![]() |
| Removing rear access panel |
![]() |
| Panel has been removed |
![]() |
| Missing socks located! |
The next step was to investigate the Hall sensor and stator.
The Hall sensor monitors the motor's rotational position, allowing the washer's control system to determine how the motor is operating. A faulty sensor can interfere with normal motor operation.
The stator is part of the motor assembly and contains the electrical windings that generate the magnetic field used to turn the rotor.
Both components were worth investigating.
My First Attempt: Testing from the Control Board
Initially, I tried to access the Hall sensor's electrical connections from the top control board assembly.
Although I was able to remove the control board, I couldn't find accessible electrical test points that would let me perform the measurements I needed.
I considered disconnecting the blue six-pin connector to reach the white and gray wires, but the connectors appeared delicate and potentially easy to damage.
I decided that forcing the issue wasn't worth the risk.
Rather than disconnect several delicate connectors and risk creating another problem, I abandoned that approach and moved to the motor assembly itself.
Getting Past the 24 mm Bolt
To access the Hall sensor, I needed to remove the motor rotor.
The rotor is secured by a large center bolt that requires a 24 mm socket.
I didn't have one available, so I borrowed a socket before continuing.
| Center rotor bolt - Remove with 24 mm socket & impact driver or wrench |
With the washer safely disconnected from power and the appropriate access established, I used a block of wood propped between the floor and rotor to help keep the rotor from spinning while loosening the bolt with an impact driver. The impact driver was very helpful. I struggled to get enough leverage with a large wrench.
That got the bolt off.
With the rotor removed, I could finally access the stator and Hall sensor assembly.
4. Removing the Rotor and Stator
With the center bolt and washer removed, I carefully pulled the rotor away from the washer.
Important: The rotor contains strong magnets. It can resist removal and may move suddenly as the magnetic force changes. Use both hands, keep your fingers clear of pinch points, and maintain control of the component throughout removal.
| K201 is the part with strong magnets. Remove carefully. |
After removing the rotor, I could access the stator assembly.
The stator is secured with six 10 mm bolts and washers. I removed these fasteners and carefully worked the stator free.
I also partially removed the plastic chassis piece identified as K290 in the service-manual exploded view. Removing its 10 mm fastener and moving the piece out of the way gave me better access to the wiring connections.
| Exposed stator assembly (K200). K290 Moved aside. |
I then disconnected the two electrical connections associated with the stator assembly:
The three-position connector for power (Windings).
The five-position connector for the (Hall Sensor)
With the assembly accessible, I could finally test the components directly.
| Hall Sensor (5-Contacts). Windings (3-Contacts) |
5. Testing the Hall Sensor with a Multimeter
This was the most important step in the repair.
Rather than replace parts based on guesswork, I wanted to determine whether the Hall sensor or stator was defective.
I referenced the LG service manual for the WT1101CW and followed the resistance-testing procedures.
| You don't need an expensive multimeter for this repair. |
Hall Sensor Resistance Test
The service manual's Hall sensor testing procedure is on page 44.
I used my multimeter to measure resistance across the specified pin combinations.
| Hall sensor testing procedure from service manual, page 44. |
The Hall sensor failed the resistance test! The readings I measured across the specified pin combinations did not match the expected results.
This tutorial assumes you know how to use a multimeter, so I won't go into every detail. Basically, you turn the dial to the appropriate resistance measurement range—in this case, MΩ (megohms) and kΩ (kilohms), as specified by the service manual for the respective tests.
Next, carefully touch the red and black multimeter probes to the conductive metal contacts inside the connector for each specified pin combination.
Tip: It takes a little finesse to keep the multimeter probes in contact with the connector pins long enough to get a stable reading. Take your time, and consider asking a partner to record the readings as you go. I found it difficult to keep track of the expected results, the pin combinations, and the different meter ranges while performing the tests. If you've made it this far, grab another coffee, take a deep breath, and find yourself a scribe to help out! 😀
The failed test results gave me a concrete reason to suspect the Hall sensor rather than simply replacing the motor assembly or other components.
Stator Resistance Test
I also tested the stator windings using the procedure documented on page 43 of the service manual.
The stator passed the resistance test across the specified pin combinations.
| Stator winding test procedure from service manual, page 43. |
This was an important distinction. The stator passed its electrical resistance checks, while the Hall sensor failed its specified test.
Based on these results, I decided to replace the Hall sensor rather than the stator.
Note: The measurements and pass/fail criteria should be taken from the service manual for the specific washer model. A resistance test is useful for identifying certain electrical faults, but passing a resistance test does not necessarily rule out every possible intermittent or operating fault.
6. Finding an Affordable Replacement Hall Sensor
Once I had identified the likely failed component, I looked for a replacement.
I purchased an aftermarket Hall sensor assembly from Amazon.
LG Original Replacement part: 6501KW2002A Washer Rotor Position Sensor Assembly
LG Substitute part: 6501KW2002B Rotor Position Sensor
Part Actually Purchased on Amazon: https://link.amazon/B0cXDMlxO (Tomoon).
Price: Approximately $13–$15.
![]() |
| Tomoon |
The part was inexpensive compared with replacing the entire motor assembly or paying for a professional service call.
Before ordering any replacement part, verify the washer's complete model number and check the replacement's compatibility information. Similar-looking parts are not necessarily interchangeable.
7. Replacing the Hall Sensor
With the replacement part in hand, I was ready to complete the repair.
The general procedure was:
Disconnect the washer from electrical power and establish safe access to the motor assembly.
Disconnect the water intake hose and drain hose as needed.
Remove the rotor center bolt and washer.
Carefully remove the rotor.
Remove the stator mounting bolts and carefully remove the stator as needed for access.
Move the K290 plastic chassis piece out of the way if necessary.
Disconnect the Hall sensor connector and remove the failed sensor assembly according to the service manual.
Install the replacement Hall sensor in the correct orientation and secure it.
Reconnect the electrical connectors and reinstall the components in reverse order.
Verify that all fasteners are secure, wiring is correctly routed, and the machine is fully reassembled before reconnecting power.
AI Generated Summary:
![]() |
| The steps are accurate - the generated images are close representations. |
Follow the model-specific service manual for the exact sensor removal procedure, connector routing, fastener requirements, and reassembly details. Do not guess at bolt torque values or connector orientation.
8. Testing the Repair
After installing the replacement Hall sensor, I reassembled the washer and tested it.
The repair worked!
The washer was able to operate normally again instead of stopping early in the cycle and displaying the LE error code.
A roughly $15 part had brought the washing machine back to life.
The best part was that I hadn't needed to replace the stator or the entire motor assembly. Testing the components first helped me narrow down the problem and avoid spending money on parts I didn't need.
9. Tools Used
Here are the tools I used during the repair:
Digital multimeter.
24 mm socket.
10 mm socket.
Ratchet wrench.
Impact driver.
Phillips screwdriver.
Channel-lock pliers.
Block of wood to help prevent the rotor from turning while loosening the center bolt.
I also needed access to the appropriate LG service manual for the resistance-testing procedures.
The multimeter was especially important. Without testing the Hall sensor and stator, I would have been left guessing which component was causing the problem.
10. Service Manual References
I used the service manual to guide the diagnosis and identify the relevant components.
The most useful references were:
Page 32: LE error code and troubleshooting guidance.
Page 43: Stator winding resistance test.
Page 44: Hall sensor testing procedure.
Page 53: Exploded view of the tub assembly and component identification, including K290.
| This is what the Service Manual looks like. |
These references were helpful for moving beyond basic troubleshooting and testing the individual components.
Final Thoughts: A $15 Repair Instead of a New Washing Machine
When my LG WT1101CW started displaying the LE error code, I initially wasn't sure whether I was dealing with a mechanical obstruction, a stator problem, or a failed Hall sensor.
After trying the basic troubleshooting steps, I opened the washer, accessed the motor assembly, and used a multimeter to test the components.
The Hall sensor failed its specified resistance test. The stator passed its resistance test. Replacing the Hall sensor resolved the problem.
The takeaway: If your LG WT1101CW washer is displaying an LE error code, don't automatically assume that the entire motor needs to be replaced. Investigate the possible causes, consult the service manual, and test the relevant components before buying replacement parts.
Of course, an LE code can have multiple causes, and these results don't guarantee that a failed Hall sensor is the problem with every LG washer displaying the same code.
But in my case, a little troubleshooting and an inexpensive replacement part were all it took.
I like fixing things when I can. It's satisfying to understand how something works, identify what's broken, and get it running again instead of throwing it away.
Sometimes the best tool in the toolbox is simply the willingness to learn something new.
— BigNate84
Practical How-Tos • DIY • Repair • Save Money!





